Image by Memories on 35mm

Developing your Own Film

No product

No product

No product

No product

Film Developing Guide for Black and White

1.

Darkroom

This needs to be done in complete darkness. If you don’t have a dark space available, you can use a changing bag. lay your developing tank out in front of you with the lid off and the reel removed. You will also need a film canister opener (for 35mm), some scissors and your film.

2.

Loading Film

Pull out the roll of film. Carefully cut the tongue of the film, leaving you with a straight edge that goes all the way across. Now pick up the reel and make sure you can feel both notches on the outer edge are aligned. You then need to slide the end of the film under the two notches until you feel it catch the sprocket holes. If the film has gone in straight you will be able to turn both sides of the reel in an alternate back and forth motion, which will move the film along as you go. Once the film is on the reel you need to put it in the tank. After the reel is in, put the lid on and turn it until it locks in place.

3.

Diluting Chemicals

You can usually find the dilution ratio for chemicals on its label. With this, you can work out how much you will need in relation to water. You will need 300ml of developer, stop and fix per 35mm film, and 500ml per 120 film.

If your developer has a dilution ratio of 1:9 and you have one 35mm film to develop. You would divide 300ml by 10 (the total of 1+9), and this would tell you that you need to mix 30ml of developer with 270ml of water. Repeat this for the three different chemicals (Stopbath, Fixer and Hypoclear).

Each chemical will also give you the time it takes to work and the temperature it works best at. When processing black and white film the standard temperature is 20°. It’s best to get your water to the right temperature first, then add in the chemistry. Now you can start your film processing.

4.

Water Wash

Fill tank with water and agitate for 2 minutes continuously. Agitate by turning the tank upside down, then back up again. Dump water out of tank.

 

Note: For every duration that the film is let to rest, bang the bottom of the tank against a hard surface before rest. This will dislodge any air bubbles that have built up on the film. 

5.

Developer

Every film and developer combination has a specific developing time so make sure you know how long your combination will need. Set a timer going and slowly pour the developer into the central funnel of the processing tank. Once it is all in, securely fit the flat lid. 

Continuously agitate for the first 30 minutes then for 10 seconds every minute until the full development time has passed. As the development time nears the end get ready to pour out your developer. Developers are usually non-reusable so be sure to pour away after each use.

Ps. Refer to the massive development chart for your developing time over here.

6.

Stop Bath

Now quickly pour in the diluted stop bath and close lid. This will completely stop development. Agitate the stop for a minute and pour back into a storage bottle. The stop can be reused many times so don’t waste it. Do a 1 minute water wash thereafter.

Note: Stopbath can be recycled. Discard when strong discolouration appears.

7.

Fixer

Fixer clears all the unexposed film emulsion and fixes the silver in the exposed parts of your image. Fixing time is important as it stabilises the image and makes it light proof. 

Total duration for this step is 6 minutes. Pour fixer into tub and close lid. Continuously agitate for the first minute then for 10 seconds every 30 minutes thereafter until 6 minutes timer is up. Pour fixer out of tank. Do a one minute water wash thereafter.

Note: Fixer can be recycled. Discard when strong discolouration appears.

8.

Hypoclear (Optional)

For best results, professional photographers treat processed film with a hypo clearing agent to speed removal of the fixer and allow more effective washing. Fill tank with wetting agent and continuously agitate for 2 minutes.

Note: Hypoclear can be recycled. Discard when strong discolouration appears.

9.

Water Wash

Total duration is 20 minutes. Fill tank and dump tank frequently for the first 2 minutes. Place tank under running water for the rest of prescribed time to remove excess chemicals.

10.

Wetting Agent/ Photo-Flo

After washing its recommended that you soak your film in the wetting agent for a minute or two, this allows the water to slip off the film more easily which helps avoids drying marks. Add wetting agent to tank filled with water. Continuously agitate for 30 seconds and pour out. 

Leave films to dry thereafter.

Image by Michael Jin

Film Developing Equipments

Find Us

3 Coleman Street, Peninsula Shopping Centre

#03-30/31/32 Singapore 179804 

WhatsApp Message: +65-8223-7153

blackmarketcamera@gmail.com

Ships within Singapore only.

We Accept

  • White Facebook Icon
  • White Twitter Icon
  • White Instagram Icon
  • White Google+ Icon

© 2020 by Black Market Camera. All Rights Reserved.